---
title: "Self-Aligning Ball Bearings: When and Why to Use Them"
date: 2026-11-09
description: "Self-aligning ball bearings are double-row ball bearings with a spherical outer ring raceway. This geometry allows the inner ring, balls and cage to tilt relati..."
source: https://en.mshjzc.com/bearing-basics/58133.html
---

# Self-Aligning Ball Bearings: When and Why to Use Them

[Self-aligning ball bearings](/self-aligning-ball-bearings.html) are double-row ball bearings with a spherical outer ring raceway. This geometry allows the inner ring, balls and cage to tilt relative to the outer ring, compensating for shaft deflection and mounting misalignment. They are the go-to choice when the shaft is long, flexible or prone to bending under load.

Start with [rolling bearing basics](/bearing-basics/58122.html) and compare with [deep groove ball bearings](/bearing-basics/58127.html) and [spherical roller bearings](/bearing-basics/58131.html).

## How the Self-Aligning Geometry Works

The outer ring raceway is ground as a spherical surface centered on the bearing axis. Two rows of balls run between this spherical raceway and two inner ring raceways. Because the outer raceway curves, the inner ring assembly can swivel by up to 2 to 3 degrees without the balls binding.

This tilt capability tolerates:

- Shaft deflection under heavy load (long shafts between supports)
- Housing bore misalignment from machining errors
- Shaft bending caused by belt tension or gear forces
- Thermal expansion that tilts the shaft relative to the housing

No other ball bearing type offers this misalignment tolerance. Deep groove and angular contact ball bearings require precise alignment between shaft and housing.

## Bore and Mounting Options

### Cylindrical Bore (1200 / 1300 / 2200 / 2300 Series)

Standard bore for press-fit mounting directly onto the shaft. Common series include 1200, 1300 (light) and 2200, 2300 (heavy).

### Tapered Bore K (1:12 Taper)

The K suffix indicates a tapered bore that mounts onto an adapter sleeve or withdrawal sleeve. This allows the bearing to be slid onto a plain shaft, positioned axially, and locked by tightening the locknut. It is far easier to install and remove than a press-fit bearing on a large shaft.

## Load Capacity and Speed

Self-aligning ball bearings carry moderate radial load and light axial load. Because of the spherical outer raceway, they cannot support heavy thrust load. Their advantage is not raw load capacity but robustness under misalignment. Speed capability is good, comparable to deep groove ball bearings of similar size.

## Cage Materials

- **Pressed steel cage** - standard, general purpose
- **Machined brass cage** - high precision or heavy vibration
- **Polyamide cage** - low noise, light weight, chemical resistance

## Typical Applications

- Conveyor rollers and belt idlers
- Fans and blowers with long shafts
- Pulleys and sheaves with misaligned shafts
- Textile and paper machinery rolls
- Agricultural machinery (long PTO shafts, tillage)
- Pump shafts where alignment is difficult to maintain

## Frequently Asked Questions

### What is the maximum misalignment angle?

Typically 2 to 3 degrees for standard series. Beyond this, the balls contact the raceway edges and premature fatigue occurs.

### Can self-aligning ball bearings carry axial load?

They can carry light axial load in either direction, but this should not be the primary load. For significant axial load, use angular contact ball bearings.

### What is the difference between 1205 and 2205?

1205 and 2205 share the same 25 mm bore but 2205 has a wider outer ring and higher load capacity. The 2200 series is the heavy version of the 1200 series.

## Related Reading

- [What Is a Rolling Bearing?](/bearing-basics/58122.html)
- [Spherical Roller Bearings for Heavy Misaligned Loads](/bearing-basics/58131.html)
- [Deep Groove Ball Bearings](/bearing-basics/58127.html)

## Need Self-Aligning Ball Bearings?

MS Bearing supplies 1200, 1300, 2200 and 2300 series in cylindrical and tapered bore variants. Adapter sleeves are available. All bearings are CE certified and dimensionally interchangeable. Send us your shaft diameter and misalignment conditions, and we will confirm the correct series.
