---
title: "Bearing Seals and Shields: Which Protection Do You Need?"
date: 2026-11-09
description: "Choosing between an open bearing, a shielded (ZZ) bearing and a sealed (2RS) bearing is not just a catalog footnote. The wrong protection leads to contamination..."
source: https://en.mshjzc.com/bearing-selection-guide/58142.html
---

# Bearing Seals and Shields: Which Protection Do You Need?

Choosing between an open bearing, a shielded (ZZ) bearing and a sealed (2RS) bearing is not just a catalog footnote. The wrong protection leads to contamination, grease loss, or overheating. This guide compares seal types and explains how to match them to your environment.

See also [load rating](/bearing-selection-guide/58136.html) and [lubrication basics](/bearing-lubrication-maintenance.html).

## Open Bearing (No Protection)

The open bearing has no seals or shields. It relies on the machine housing to keep dirt out and on external lubrication (oil bath, circulating oil, or central grease). Open bearings have the highest speed limit and are used when the machine itself provides adequate sealing and lubrication.

## Shielded (Z or ZZ)

A thin pressed steel disc is attached to the outer ring on one or both sides. It does not touch the inner ring, so there is no friction. It blocks large dust particles and retains grease, but does not stop fine dust, water vapor or liquid splash.

- **Z** - one side shielded
- **ZZ / 2Z** - both sides shielded

Shielded bearings are pre-greased at the factory. They are suitable for clean, dry environments: electric motors, fans, household appliances.

## Contact Seal (RS or 2RS)

A rubber seal lip touches the inner ring land. This provides much better sealing against dust, moisture and liquid, but the contact generates friction heat and reduces the speed limit by about 20 to 30 percent.

- **RS** - one side contact seal
- **2RS / 2RSH / 2RSR** - both sides contact seals

Common rubber materials:

- **Nitrile (NBR)** - standard, -30 to +100 C, good grease resistance
- **FKM / Viton** - high temperature up to +180 C, chemical resistance
- **Silicone** - low temperature flexibility, lower mechanical strength

## Non-Contact Seal (V Labyrinth)

A rubber seal that does not touch the inner ring but has a narrow labyrinth gap. It provides better protection than a steel shield with almost no friction. Used in dirty environments where speed matters.

## How to Choose

<table border="1" cellpadding="6" cellspacing="0" style="border-collapse:collapse;"><tr><th>Environment</th><th>Recommended Protection</th></tr><tr><td>Clean, dry, high speed</td><td>Open or ZZ</td></tr><tr><td>Normal indoor industrial</td><td>ZZ or 2RS</td></tr><tr><td>Dusty, occasional splash</td><td>2RS (NBR)</td></tr><tr><td>Washdown, food industry</td><td>2RS (FKM or silicone), stainless steel</td></tr><tr><td>High temperature above 100 C</td><td>Open with external seal, or FKM 2RS</td></tr><tr><td>Very dirty (construction, agriculture)</td><td>2RS plus housing lip seal</td></tr></table>

## Frequently Asked Questions

### Can I relubricate a 2RS bearing?

Sealed bearings are greased for life. You can inject a small amount of fresh grease through a housing fitting, but over-greasing causes heat. Most applications never relubricate sealed bearings.

### Which is faster, ZZ or 2RS?

ZZ is faster because there is no contact friction. 2RS runs about 20 to 30 percent slower in catalog speed ratings.

### Can I add seals to an open bearing myself?

No. The internal clearance and grease fill volume are designed for the seal type. Adding a seal later traps heat and overfills with grease, causing premature failure.

## Related Reading

- [Deep Groove Ball Bearings](/bearing-basics/58127.html)
- [Fitting Tolerances](/bearing-selection-guide/58137.html)
- [Lubrication and Maintenance](/bearing-lubrication-maintenance.html)

## Need Sealed Bearings?

MS Bearing supplies open, ZZ shielded and 2RS sealed versions of all standard series, in NBR and FKM rubber. Send us your environment and speed, and we will recommend the correct protection option.
