---
title: "Lubricant Viscosity: How to Choose the Right Oil Grade"
date: 2026-11-09
description: "Viscosity is the single most important property of a bearing lubricant. Too thin and the oil film collapses under load. Too thick and the bearing churns oil and..."
source: https://en.mshjzc.com/bearing-lubrication-maintenance/58147.html
---

# Lubricant Viscosity: How to Choose the Right Oil Grade

Viscosity is the single most important property of a bearing lubricant. Too thin and the oil film collapses under load. Too thick and the bearing churns oil and overheats. This guide explains ISO viscosity grades and how to pick the right one for your bearing.

See also [grease vs oil](/bearing-lubrication-maintenance.html) and [speed limits](/bearing-selection-guide/58139.html).

## ISO VG Viscosity Grades

Industrial oils are classified by ISO VG (Viscosity Grade). The number is the oil's kinematic viscosity at 40 C in mm2/s (cSt).

<table border="1" cellpadding="6" cellspacing="0" style="border-collapse:collapse;"><tr><th>ISO VG</th><th>Viscosity at 40 C</th><th>Typical Use</th></tr><tr><td>VG 22</td><td>22 cSt</td><td>Very high speed, small bearings</td></tr><tr><td>VG 32</td><td>32 cSt</td><td>High-speed electric motors, spindles</td></tr><tr><td>VG 46</td><td>46 cSt</td><td>General light industrial, pumps</td></tr><tr><td>VG 68</td><td>68 cSt</td><td>General industrial gearboxes, moderate speed</td></tr><tr><td>VG 100</td><td>100 cSt</td><td>Heavy load, moderate speed</td></tr><tr><td>VG 150</td><td>150 cSt</td><td>Heavy gearboxes, low speed</td></tr><tr><td>VG 220</td><td>220 cSt</td><td>Heavy industrial, high temperature</td></tr><tr><td>VG 320 / 460</td><td>320-460 cSt</td><td>Extreme load, very slow speed</td></tr></table>

## Minimum Required Viscosity

For a bearing to maintain an elastohydrodynamic (EHL) oil film, the oil must have a certain minimum viscosity at operating temperature. This depends on bearing size and speed:

- Small bearings, high speed - minimum 12 to 20 cSt at operating temperature
- Medium bearings, moderate speed - minimum 20 to 30 cSt
- Large bearings, heavy load - minimum 30 to 50 cSt

Because oil thins as it heats up, the operating viscosity is always lower than the 40 C catalog value. A VG 68 oil at 80 C may behave like a VG 22. If that drops below the minimum, the bearing runs in boundary lubrication and fails early.

## Viscosity Index

The viscosity index (VI) measures how much the oil thins as temperature rises. Mineral oils typically have VI around 95. Synthetic oils (PAO, ester) have VI 140 or higher, meaning they stay viscous at high temperature. For machines that see wide temperature swings, choose high-VI synthetic oil.

## How to Select

1. Find the operating temperature of the inner ring (typically 10 to 20 C above housing temperature).
2. Look up the oil's viscosity at that temperature from its temperature-viscosity chart.
3. Compare with the minimum required viscosity for your bearing size and speed.
4. If the operating viscosity is too low, step up one ISO grade.
5. If the bearing runs at very high speed, step down one grade to reduce churning heat.

## Frequently Asked Questions

### What viscosity grease is used in electric motors?

Most motor greases use ISO VG 68 to 100 base oil at NLGI 2 consistency. This balances high speed and load capacity.

### Can I use a thicker oil to protect a worn bearing?

A thicker oil may reduce noise temporarily, but it will not restore a damaged raceway. It also increases heat and drag. Replace the bearing instead.

### Why does my oil look thinner after summer?

Oil viscosity drops as temperature rises. A VG 68 oil at 80 C may be as thin as VG 22. This is normal, but if it drops below the minimum, the bearing needs a higher viscosity grade or a cooler operating temperature.

## Related Reading

- [Grease vs Oil](/bearing-lubrication-maintenance.html)
- [Grease Consistency NLGI](/bearing-lubrication-maintenance.html)
- [Bearing Speed Limits](/bearing-selection-guide/58139.html)

## Need Lubricant Recommendation?

MS Bearing can recommend the correct grease or oil viscosity for your bearing based on speed, load and temperature. Send us your operating conditions, and we will specify the lubricant grade and relubrication interval.
