---
title: "6204 bearing specification"
date: 2026-11-10
description: "What are the 6204 bearing specifications? The 6204 bearing is a 20 mm bore, 47 mm outer diameter, 14 mm width deep groove ball bearing with a 12.75 mm chamfer d..."
source: https://en.mshjzc.com/blog/58204.html
---

# 6204 bearing specification

What are the 6204 bearing specifications? The 6204 bearing is a 20 mm bore, 47 mm outer diameter, 14 mm width deep groove ball bearing with a 12.75 mm chamfer distance, rated C3 clearance, and dynamic load capacity up to 12.3 kN per MS Bearings factory data 2024 and ISO 15:2017. This guide gives the exact dimensions, load and speed ratings, application fits, and sourcing criteria buyers use to specify or replace 6204 bearings in motors, gearboxes, pumps, conveyors, and agricultural machinery.

How big is a 6204 bearing? It has a bore (d) of 20 mm, an outer diameter (D) of 47 mm, and a width (B) of 14 mm. The basic dynamic load rating (C) is typically **12.3 kN** and the static load rating (C0) is around **6.95 kN** per ISO 15:2017. Typical limiting speed is **14,000 RPM** and reference speed is **8,500 RPM** at grease lubrication. The standard chamfer dimension (r min) is 1.0 mm on each side, which controls edge clearance and tolerance fit for shafts and housings rated H7/H6 per DIN 620 and ABMA standards.

Are 6204 and 6205 bearings the same? No, they are not interchangeable. The 6205 bearing has a 25 mm bore and 52 mm outer diameter, making it larger than the 6204, which is why buyers must check the exact 6204 bearing specification before ordering. The table below lists the main dimensional and performance differences for reference:

<table><thead><tr><th>Parameter</th><th>6204</th><th>6205</th></tr></thead><tbody><tr><td>Bore d (mm)</td><td>20</td><td>25</td></tr><tr><td>Outer D (mm)</td><td>47</td><td>52</td></tr><tr><td>Width B (mm)</td><td>14</td><td>15</td></tr><tr><td>Dynamic C (kN)</td><td>12.3</td><td>14.0</td></tr><tr><td>Static C0 (kN)</td><td>6.95</td><td>7.85</td></tr><tr><td>Limiting speed (RPM)</td><td>14,000</td><td>13,000</td></tr></tbody></table>

Which applications use a 6204 bearing? The 6204 fits electric motors, gearboxes, centrifugal pumps, conveyor pulleys, agricultural machinery, and light automotive duty. In an electric motor, the 6204 supports radial loads and moderate axial loads with low noise and vibration. In a gearbox, it stabilizes shaft alignment and reduces backlash under shock loads. On conveyors, it handles continuous rotation with moderate loads and temperature swings. In agricultural machinery, sealed 6204 variants protect against dust and moisture in dusty, wet environments.

1. Check the bore, outer diameter, and width against the housing and shaft print before ordering.
2. Select the correct seal type: open, metal shield, or rubber seal for dusty environments.
3. Confirm lubrication type: grease for general use, oil for high speed and high temperature.
4. Match clearance class C3 for motor and gearbox applications with thermal expansion or vibration.
5. Verify the load rating meets the duty cycle; overloading by 20% reduces life by 50%.
6. Use the correct tolerance fit: H7 on shafts, H7 on housings with slight press fit for rotating inner ring loads.

> Expert tip: For applications above 12,000 RPM or temperatures above 120°C, switch to a high-temperature grease, increase internal clearance to C4, and re-calculate the dynamic load rating using SKF 2024 catalog methods.

How do you select the correct 6204 bearing for a motor? Measure the shaft diameter at the bearing seat and confirm housing bore with a bore gauge. Check the load profile: radial loads dominate in belt drives, while axial loads rise in pumps with impeller thrust. Determine the required life L10 using the formula L10 = (C/P)^3 at 10,000 RPM for a 12.3 kN dynamic rating and match sealing to the environment. For severe dust or water, use a 2RS rubber seal; for very high speed, use an open or metal shield design. Choose C3 clearance for motors with heat buildup; C0 or C2 is acceptable in cool, steady-state machines. Re-check tolerance fits for shaft and housing: H7 on shaft and H7 on housing is standard; use H6 on shaft for slight rotation under load to prevent creep.

How to install and lubricate a 6204 bearing correctly? Install with a press and a sleeve that contacts the inner ring only; never strike the outer ring directly. For heat mounting, heat the inner ring to **80–90°C** maximum and avoid heating seals or shields. Use aSKF-approved electric motor grease (e.g., LGMT 2/1000) at 100% fill for initial lubrication and re-lube at 2,500 hours under moderate duty. Confirm the correct fit using H7 on shafts and H7 on housings with a slight press fit; for rotating outer ring loads, use a press fit in the housing. Re-check backlash and runout after mounting: target **0.05 mm** radial runout for precision shafts.

Why do 6204 bearings fail early? Common causes include excessive radial or axial load, inadequate lubrication, contamination, incorrect fits, misalignment, and thermal stress. Use the table below to match symptoms to causes and fixes:

<table><thead><tr><th>Symptom</th><th>Likely cause</th><th>Fix</th></tr></thead><tbody><tr><td>Noise at low speed</td><td>Contamination, insufficient grease, brinelling</td><td>Clean housing, re-grease, replace bearing</td></tr><tr><td>High temperature</td><td>Over-greasing, wrong grease, tight fit</td><td>Adjust fill to 30–50%, correct fit, upgrade grease</td></tr><tr><td>Vibration at high speed</td><td>Misalignment, unbalance, wrong clearance</td><td>Re-align shaft, balance rotor, use C3 clearance</td></tr><tr><td>Bearing creep</td><td>Loose fit on shaft or housing</td><td>Adjust fit to H6 on shaft, use flanged housing</td></tr></tbody></table>

- Use a laser alignment tool to verify shaft alignment within **0.05 mm** per 100 mm of span.
- Monitor temperature with a handheld IR thermometer; keep bearing housing below **85°C** for standard grease.
- Schedule re-lubrication at 2,500 hours under moderate duty and 5,000 hours under light duty.
- Replace bearings in pairs to maintain load distribution and avoid uneven wear.

What are the key 6204 bearing specifications at a glance? Bore 20 mm, outer diameter 47 mm, width 14 mm, dynamic load 12.3 kN, static load 6.95 kN, limiting speed 14,000 RPM, C3 clearance, standard seal options open, metal shield, and rubber seal.

Which market standards and certifications apply to 6204 bearings? MS Bearings supplies 6204 bearings with ISO 9001:2015 quality systems, RoHS-compliant materials, and 12-month warranty under factory direct supply. Export destinations include Germany, USA, Italy, India, and Thailand. For OEM replacements, 6204 bearings meet DIN 620 and ABMA standards for dimensions, tolerances, and load ratings. The factory ships 24-hour lead time on standard sizes and provides technical data sheets per SKF 2024 catalog equivalents.

What is the bore size of a 6204 bearing?

20 mm bore with 47 mm outer diameter and 14 mm width per ISO 15:2017.

How much load can a 6204 bearing handle?

Dynamic load capacity up to 12.3 kN and static load 6.95 kN at reference speed 8,500 RPM.

Are 6204 and 6205 bearings interchangeable?

No, 6205 has a 25 mm bore and 52 mm outer diameter, so the 6204 will not fit the same housing or shaft.

What applications use 6204 bearings?

Electric motors, gearboxes, pumps, conveyors, and agricultural machinery where moderate radial and axial loads occur.

If you need 6204 bearing specifications tailored to your motor or gearbox, visit mshjzc.com to request a data sheet and confirm fit, load, and lubrication for your application. MS Bearings supplies factory-direct 6204 bearings with 12-month warranty, 24-hour shipping, and export to 30+ countries.
