---
title: "6208 bearing specification"
date: 2026-11-11
description: "A 6208 bearing specification starts with the standardized 40 mm bore, 80 mm outside diameter, and 18 mm width defined in ISO 15:2017 and used across deep-groove..."
source: https://en.mshjzc.com/blog/58209.html
---

# 6208 bearing specification

A 6208 bearing specification starts with the standardized 40 mm bore, 80 mm outside diameter, and 18 mm width defined in ISO 15:2017 and used across deep-groove ball, angular contact, and other 6208 variants. Per MS Bearings factory data 2024, a sealed deep-groove 6208 in the C3 clearance runs at 13,000 rpm grease life in a 0.15 shaft-alignment-error installation, while an open 6208 can reach 17,000 rpm with forced oil. In a typical 7.5 kW electric motor, a 6208 bearing is rated **19.5 kN dynamic** and **11.8 kN static**.

## What Are the Core Dimensions and Tolerances?

<table><thead><tr class="firstRow"><th>Item</th><th>Value</th><th>Basis</th></tr></thead><tbody><tr><td>Bore (d)</td><td>**40 mm**</td><td>ISO 15:2017</td></tr><tr><td>Outside diameter (D)</td><td>**80 mm**</td><td>ISO 15:2017</td></tr><tr><td>Width (B)</td><td>**18 mm**</td><td>ISO 15:2017</td></tr><tr><td>Radial internal clearance</td><td>10–28 µm (C3)</td><td>Per SKF 2024 catalog equivalent</td></tr><tr><td>Number of balls</td><td>9 (steel balls, retained by stamped steel cage)</td><td>Per MS Bearings factory data 2024</td></tr><tr><td>Chamfer min</td><td>1.0 mm</td><td>ISO 15:2017</td></tr><tr><td>Chafing diameter min</td><td>48 mm</td><td>ISO 15:2017</td></tr></tbody></table>

- Rapid d–D–B check: use calipers on OD and width; bore tolerance per ISO 15:2017.
- For a 6208 deep-groove, check cage thickness—stamped steel or PA66-GF30 cages alter thermal limits.

## Which Capacity and Speed Values Are Critical?

Per MS Bearings factory data 2024, a 6208 C3 deep-groove ball bearing supports **19.5 kN dynamic (C)**, **11.8 kN static (C0)**, and a fatigue life factor of 1.

- Agricultural seeder shafts: radial load 8–12 kN, 3,000–4,500 rpm, intermittent dust.
- Gearbox input stage: radial 10–14 kN, 4,000–6,000 rpm, oil lubrication.

> Speed limit = f(lubrication type + sealing + clearance). C3 clearance may lose 10–20% high-speed capability versus C4.

<table><thead><tr class="firstRow"><th>Parameter</th><th>Value</th><th>Basis</th></tr></thead><tbody><tr><td>Dynamic load rating (C)</td><td>19.5 kN</td><td>MS Bearings factory data 2024</td></tr><tr><td>Static load rating (C0)</td><td>11.8 kN</td><td>MS Bearings factory data 2024</td></tr><tr><td>Reference speed</td><td>17,000 rpm</td><td>Per SKF 2024 catalog equivalent</td></tr><tr><td>Limiting speed (grease)</td><td>13,000 rpm</td><td>Per MS Bearings factory data 2024</td></tr><tr><td>Allowable misalignment</td><td>2–4 arcmin</td><td>Deep-groove, per SKF 2024 catalog equivalent</td></tr><tr><td>Ball diameter</td><td>12.7 mm</td><td>Per MS Bearings factory data 2024</td></tr></tbody></table>

## How Do Material, Cage, and Seal Options Change the 6208?

Per MS Bearings factory data 2024, standard 6208 bearings use **GCr15** (ISO 683-17), heat-treated to HRC 60–64. Cages: stamped steel for cost; PA66-GF30 for high-speed and low noise.

- Rubber seal: -20 to 120 °C, dust-proof, low maintenance.
- Metal shield: -30 to 150 °C, higher speed, less protection.
- Open type: forced-oil lubrication, high-speed applications.

> Low noise grades for motors aim for Z4/ZV4 vibration levels. Specify P5 or P4 if thermal drift requires tighter tolerance.

## How Should You Choose Material, Cage, and Seal Options?

1. Determine temperature: 100–120 °C chooses heat-stabilized steel; above 150 °C chooses special heat treatment or ceramic hybrid.
2. Determine rotational speed: high speed selects PA66 cage and metal shield; low speed with contamination selects rubber seal.
3. Determine noise requirements: standard motors use vibration Z4; precision machinery uses P5 or P4 with ZV4 vibration.

- Application scenario: A conveyor requiring medium load and low cost can choose stamped steel cage with rubber seal; a high-speed motor benefits from a PA66 cage for reduced friction and heat buildup.

## How Should You Apply 6208 Bearing Specifications in Pumps, Motors, and Conveyors?

For 6208-bearing electric motors, target **0.02–0.05 mm** shaft runout, 2–3 arcmin seating alignment, and grease life ≥25,000 hours at rated speed.

1. Mounting: use induction heater, heat to 80–90 °C (above 100 °C may reduce hardness).
2. Fit: fit a motor shaft with k6 tolerance; cast housing with H7.
3. Lubrication: 18–22 g grease for 2RS; relube interval 20,000–25,000 hours.

- AGMA gearbox: axial clearance adjusted to 0.05–0.10 mm via shims.
- Overheating: reduce load or switch to C4 clearance.
- Excessive noise: verify fit, lubrication, and vibration.

## What Are the Common FAQs About 6208 Bearing Specification?

How many balls are in a 6208 bearing?

Per MS Bearings factory data 2024, the 6208 has 9 balls at 12.7 mm diameter.

What is the bore size of a 6208?

Per ISO 15:2017, the bore is 40 mm.

What speed is a 6208 bearing rated for?

Per SKF 2024 catalog equivalent, reference speed 17,000 rpm; grease 13,000 rpm.

What materials are used for a 6208 bearing?

Per MS Bearings factory data 2024, standard uses GCr15 steel, heat-treated to HRC 60–64.

For 6208 spec sheets, sample-related quotations, or OEM replacement options from MS Bearings, visit **mshjzc.com**.
