---
title: "Deep Groove Ball Bearing Suffixes ZZ, 2RS, C3 and P5 Explained"
date: 2026-11-22
description: "The suffixes ZZ, 2RS, C3, and P5 stamped after a deep groove ball bearing number each define one physical feature: ZZ means metal shields on both sides, 2RS mea..."
source: https://en.mshjzc.com/blog/58260.html
---

# Deep Groove Ball Bearing Suffixes ZZ, 2RS, C3 and P5 Explained

The suffixes ZZ, 2RS, C3, and P5 stamped after a deep groove ball bearing number each define one physical feature: **ZZ** means metal shields on both sides, **2RS** means rubber contact seals on both sides, **C3** means radial internal clearance larger than standard, and **P5** means the bearing is ground to tolerance class 5, tighter than normal production grade. None of them changes the boundary dimensions — a sealed 6205 has exactly the same 25 × 52 × 15 mm envelope as an open one per ISO 15:2017 — so seal type, clearance and precision can be combined freely to suit the application. The marking system follows the DIN 623-1 designation convention used by SKF, FAG, NSK, NTN and virtually every manufacturer in Asia, which is why a 2RS bearing from a Chinese factory directly replaces an SKF 2RS1 or an NSK DDU without any design change.

## ZZ Meaning: Metal Shields on Both Sides

ZZ (written 2Z by SKF and FAG) denotes two pressed-steel shields fixed into the outer ring. The shield does not touch the rotating inner ring, so it adds almost no friction torque and preserves the full open-bearing limiting speed per the SKF 2024 catalog. Shields block coarse dust, chips and splashed oil but do not seal against water, mist or fine powder; the bearing arrives grease-filled for life.

- Non-contact design: near-zero added torque, catalog speed unchanged
- Steel construction: the shield survives the full grease temperature range, typically −30 °C to +120 °C
- Best for fan motors, power tools, office equipment and dry indoor conveyors
- Weakness: no protection against washdown, rain, condensation or abrasive powder

## 2RS Meaning: Rubber Contact Seals and Their Brand Aliases

2RS means two NBR (nitrile rubber) lip seals carried in sheet-metal rings. The lip runs under light preload on the inner-ring shoulder, so friction torque rises measurably and the catalog limiting speed drops slightly versus a shielded bearing per the SKF 2024 catalog. NBR seals handle continuous service from about −30 °C to +100 °C; FKM (fluorocarbon) options extend this to roughly +150 °C, which matters for pumps and compressors near hot process lines. The same seal design carries different suffixes by brand, and buyers should treat them as functionally identical:

- **2RS1** — SKF
- **2RSR** — FAG and INA
- **DDU** — NSK
- **LLU** — NTN

> **Practical tip:** NBR degrades in caustic food-washdown chemicals and above +100 °C. For dairy, beverage or hot-oil duty, specify FKM seals or all-stainless sealed variants instead of standard 2RS.

## ZZ or 2RS: How to Choose the Sealing Suffix

<table><thead><tr><th>Factor</th><th>ZZ (shields)</th><th>2RS (rubber seals)</th></tr></thead><tbody><tr><td>Contact with inner ring</td><td>None</td><td>Light lip contact</td></tr><tr><td>Water and mist protection</td><td>Poor</td><td>Good</td></tr><tr><td>Friction torque</td><td>Almost zero</td><td>Noticeably higher</td></tr><tr><td>Limiting speed</td><td>Full open-bearing value</td><td>Slightly reduced</td></tr><tr><td>Seal temperature limit</td><td>Grease-limited, about +120 °C</td><td>−30 °C to +100 °C (NBR)</td></tr><tr><td>Relubrication</td><td>Possible in housings with lube holes</td><td>Not practical; maintenance-free</td></tr><tr><td>Typical duty</td><td>Fan motors, power tools</td><td>Water pumps, conveyor rollers, agricultural machinery</td></tr></tbody></table>

A workable field rule: choose 2RS whenever moisture, washdown or fine dust is present; choose ZZ when only coarse dust exists and maximum speed matters.

## C3 Meaning: Radial Internal Clearance

C3 is a radial internal clearance group — the distance one ring can move radially relative to the other before mounting. CN (also written C0) is the standard group; C3 is one step larger. Values per ISO 5753 for deep groove ball bearings with 24–30 mm bores:

<table><thead><tr><th>Group</th><th>Radial clearance (µm)</th><th>When to specify</th></tr></thead><tbody><tr><td>C2</td><td>1–11</td><td>Precision, cool-running, light fits</td></tr><tr><td>CN (C0)</td><td>5–20</td><td>Default; loose or transition fits</td></tr><tr><td>C3</td><td>13–28</td><td>Interference fits, warm-running assemblies</td></tr><tr><td>C4</td><td>23–41</td><td>Hot environments; both rings interference-fitted</td></tr></tbody></table>

C3 is the default clearance for electric motors for three reasons:

1. A press-fitted inner ring expands on the shaft and consumes clearance
2. Rotor heat reaches the inner ring before the outer ring, shrinking clearance further
3. Operating clearance must stay positive — if it closes to zero, the balls preload, heat spikes and the bearing seizes

> **Warning:** Do not overspecify clearance. C4 on a lightly fitted fan bearing raises vibration and noise. Shaft fits of k5 or m5, or ambient temperatures above roughly 80 °C, are the usual triggers for C3.

## P5 Meaning: Tolerance Class 5

P5 is a dimensional and running-accuracy grade defined in ISO 492. It tightens bore, outside-diameter, width and radial-runout tolerances from the normal P0 grade down to single-digit microns. For a 25 mm bore:

<table><thead><tr><th>Class</th><th>Bore deviation (µm)</th><th>Typical duty</th></tr></thead><tbody><tr><td>P0 (normal)</td><td>0/−10</td><td>General machinery, standard motors</td></tr><tr><td>P6</td><td>0/−8</td><td>Better-grade electric motors, fans</td></tr><tr><td>P5</td><td>0/−6</td><td>Machine-tool spindles, high-speed motors, instrumentation</td></tr><tr><td>P4</td><td>0/−5</td><td>Precision spindles, aerospace equipment</td></tr></tbody></table>

P5 controls geometry only — not seals or clearance — and is commonly ordered as a combination such as C3 + P5 for a high-speed spindle. The tighter OD, width and runout limits explain the price premium over P0; standard motor and conveyor duty rarely justifies it.

## How to Read a Full Designation, Suffix by Suffix

Take 6205-2RS-C3-P5 as a worked example:

1. **6205** — light series, 25 mm bore, 52 mm outside diameter, 15 mm width per ISO 15
2. **2RS** — NBR contact seals on both faces
3. **C3** — clearance group larger than normal
4. **P5** — tolerance class 5

Notation order and spelling vary by brand — NSK writes 6205DDUC3, SKF writes 6205-2RS1/C3, FAG writes 6205-2RSR-C3 — but the engineering content is identical. Other suffixes you will meet on deep groove ball bearings:

- **N / ZNR** — snap-ring groove, or shield plus snap ring
- **M / TN** — machined brass cage or pressed polyamide cage
- **K** — tapered bore, 1:12
- **E** — reinforced internal design with higher dynamic load rating
- **C0 / C1 / C2 / C4** — other clearance groups
- **P4 / P2** — higher precision classes
- **V2 / EMQ** — quiet-running electric-motor-quality grades

## Frequently Asked Questions

Suffix codes are a purchasing language: once you can read ZZ, 2RS, C3 and P5, you can order an exact replacement from any factory in the world. MS Bearings, an ISO 9001:2015-certified factory in Kunshan, China, produces deep groove ball bearings in all common suffix combinations, including OEM equivalents for SKF, FAG and NSK designations, with a 12-month warranty. Stock items ship within 24 hours per MS Bearings factory data 2024, and the factory exports to buyers in more than 30 countries. If you need help decoding a designation or confirming the right clearance and seal combination for your equipment, the engineering team at en.mshjzc.com can cross-check the code and quote factory-direct.
