Fine machining a Chinese precision bearing means holding ring bore and outer diameter tolerances within IT4–IT5, roundness under 2 µm, and surface roughness Ra ≤ 0.2 µm on raceway finish surfaces, so the finished part can meet ISO 15:2017 and P4/P2 grade requirements.
This guide covers the machining process, tolerance classes, surface finish specifications, inspection methods, and material quality criteria for fine machining Chinese precision bearings. It applies to deep groove ball, angular contact, cylindrical roller, tapered roller, spherical roller, thrust, and custom OEM bearings.
Fine Machining Process Steps for Chinese Precision Bearing Races
- Bar stock blanking and forging. Blanks are cut from bearing steel bar and forged at 1,100–1,200 °C to form rough rings, followed by normalizing at 850–900 °C to refine grain structure.
- Rough turning. CNC lathes remove the bulk of material, leaving 1.5–2.5 mm of stock on raceway diameters.
- Annealing. Full annealing at 780–820 °C restores machinability and hardness uniformity before finishing.
- Semi-finish turning. Ring bore and outer diameter are turned to ±0.02 mm of finished size.
- Heat treatment. Quenching and tempering hardens races to HRC 60–64. Deep cryogenic treatment at –120 °C is used on P4 and P2 grades.
- Fine grinding. Sequential grinding with CBN or aluminum oxide wheels brings bore and outer diameter to final tolerance ±0.005 mm.
- Super finishing. Honing and lapping with abrasive films achieve raceway roughness Ra 0.05–0.1 µm and waviness 0.2–0.5 µm.
- Final inspection. All critical surfaces are verified with CMM, roundness testers, and profilometers.
Tolerance Standards and Fine Machining Grade Comparison
A Chinese precision bearing must be machined to meet the ISO 15:2017 tolerance class. The table below compares the main grades and the machining capability required.
| ISO Grade | Bore Tolerance (0–80 mm) | OD To width Tolerance | Roundness | Typical Use |
|---|---|---|---|---|
| P0 (Standard) | +0 / –12 µm | +0 / –15 µm | 15–20 µm | General motors, pumps, agricultural machinery |
| P6 | +0 / –8 µm | +0 / –10 µm | 8–10 µm | Gearboxes, conveyors, automotive auxiliary |
| P5 | +0 / –6 µm | +0 / –8 µm | 5–6 µm | Electric motors, machine tools, compressors |
| P4 | +0 / –4 µm | +0 / –5 µm | 2–4 µm | High-speed spindles, robotics, CNC |
| P2 | +0 / –2.5 µm | +0 / –3 µm | 1–2 µm | Aerospace, medical, high-end machine tools |
Fine machining Chinese precision bearing components to P4 or P2 grade requires in-process temperature control at 20 ± 0.5 °C. Thermal drift of 1 °C on an 80 mm part can introduce 0.8 µm of error.
Surface Finish Requirements for Chinese Precision Bearing Raceways
- Raceway roughness must be Ra ≤ 0.1 µm for P5 and P4 grades, and Ra ≤ 0.05 µm for P2.
- Racing waviness must be controlled below 0.5 µm to prevent noise and vibration.
- Rolling element surface finish must be Ra 0.025–0.05 µm.
- Grinding burn must be zero. A visual etch test or nital check is required after every grind cycle.
- Residual compressive stress on the raceway must exceed –400 MPa to extend fatigue life.
At MS Bearings, every fine machined Chinese precision bearing race is measured with a Mahr Martest and a Taylor Hobson Form Talysurf before assembly.
Inspection Methods for Fine Machining Chinese Precision Bearing Dimensions
Fine machining Chinese precision bearing inspection must include the following methods.
- Bore and outer diameter gauges: air gauges or electronic plug gauges with resolution 0.1 µm.
- Roundness measurement: CMM or dedicated roundness tester, evaluating inner and outer raceway profiles.
- Surface roughness: contact profilometer over a 0.8 mm cut-off length.
- Gear tooth flank and raceway waviness: specialized waviness testers for 0.2–0.5 µm evaluation.
- Automatic vision systems: 100% inspection of roller and ball surfaces for surface defects.
- Residual stress XRD: spot checks on high-speed and P4/P2 grade races.
A fine machined Chinese precision bearing at P4 grade must have bore taper under 1.5 µm over a 100 mm gauge length. Taper causes wedge loading and premature failure.
Material Quality for Chinese Precision Bearing Fine Machining
Fine machining a Chinese precision bearing depends on the raw steel quality. The table compares the main material grades and their suitability.
| Material Grade | Hardness (HRC) | Carbides | Fatigure Life | Suitable Grade |
|---|---|---|---|---|
| GCr15 (China GB/T 18254) | 60–64 | Fine, uniform | 1.0x baseline | P0–P5 |
| GCr15SiMn | 60–64 | Slightly higher | 1.1x baseline | P5–P4 |
| SKF-2 / SUJ2 (JIS) | 60–64 | Very fine | 1.3x baseline | P4 |
| M50 / M42 (working temp) | 62–65 | Minimal | 1.5x baseline | P4 / P2 high-temp |
Decarburized layers over 0.02 mm are rejected. Inclusion content must be below ASTM E45 severity 1 for P4 and P2 grades.
Applications and Performance of Fine Machining Chinese Precision Bearing Types
Fine machining Chinese precision bearing variants are engineered for different operating conditions. The table summarizes typical applications and performance limits.
| Bearing Type | Limiting Speed | Temperature Range | Typical Application |
|---|---|---|---|
| Deep Groove Ball | 15,000–30,000 RPM | –25 to 120 °C | Electric motors, pumps, compressors |
| Angular Contact | 12,000–25,000 RPM | –30 to 150 °C | Machine tool spindles, CNC |
| Cylindrical Roller | 8,000–18,000 RPM | –20 to 140 °C | Gearboxes, conveyors |
| Tapered Roller | 6,000–15,000 RPM | –20 to 150 °C | Automotive, construction |
| Spherical Roller | 5,000–12,000 RPM | –30 to 200 °C | Wind turbines, heavy machinery |
Fine machining Chinese precision bearing parts can achieve rated life L10 ≥ 50,000 hours under correct load and speed conditions, per ISO 281.
