sales@cnprv.com

+86 15862366271 (WhatsApp/WeChat)

6305 Bearing Specification: Complete Size, Load, Speed & Tolerance Guide

Home / Blogs / Info
MS Bearing WareHouse
author admin 12 November, 2026

The 6305 bearing specification covers a 25 mm bore, 62 mm outer diameter and 17 mm width, with dynamic C = 22.4–23.5 kN and static C₀ = 11.5–12.5 kN per ISO 15:2017 and MS Bearings factory data 2024. It is a single-row deep groove ball bearing in the 63 series, with a 17 mm width.

Are all 6305 bearings identical? No. The bearing is defined by its ISO 15 dimensions, but C and C₀ ratings, tolerance class (ABEC 1, 3, 5 or ISO P0/P6/P5/P4), seal type and clearance vary by manufacturer. A 6305-ZZ from one brand can carry a different load rating than a 6305-2RS from another.

This guide covers the dimensional 6305 bearing specification, load and speed ratings, tolerances, materials, seals, application fit, and how to read a 6305 bearing drawing.

What are the dimensions of a 6305 bearing?

Per ISO 15:2017 and the MS Bearings 2024 catalog, the 6305 bearing specification is:

Bore (d)OD (D)Width (B)FEr minrs minr1-2 min
25 mm62 mm17 mm34 mm49 mm1.0 mm1.0 mm0.6 mm

The 6305 bearing size chart is fixed: 25 × 62 × 17 mm. The F and E values control shaft and housing shoulder clearance, which matters when the bearing is pressed onto a shaft or into a housing.

Tip: A 6305 bearing has the same outer and width dimensions as a 6205 bearing of the same bore size, but not the same load rating. Do not swap 6205 and 6305 loads without checking C and C₀.

How much load can a 6305 bearing take?

What are the load ratings? In the 63 series deep groove ball family, a 6305 typically carries C = 22.4–23.5 kN and C₀ = 11.5–12.5 kN, depending on the manufacturer. Values below are for the standard 63 series pattern and may change with tolerance, cage and seal.

PropertyTypical value (63 series)Note
Dynamic C22.4–23.5 kNRotating load for L₁₀ life
Static C₀11.5–12.5 kNPer ISO 15:2017
Reference speed24,000–26,000 RPMGrease, oil, or lab data
Limiting speed14,000–15,000 RPMOil, grease, seal, cage

How do I calculate required life? Use L₁₀ = (10⁶ / 60N) × (C/P)³ for ball bearings. N = RPM, P = equivalent dynamic load in kN. For a 10,000-hour target, a 6305 with C = 23 kN handles roughly 4–5 kN at 3,000 RPM.

  1. Calculate equivalent load P.
  2. Divide C by P.
  3. Raise to the power of 3 for ball bearings.
  4. Convert to hours with N.

If the 6305 lives in a motor, the load is mostly radial. In a pump or conveyor, verify axial load against C₀ and the bearing's axial capacity.

What speed and temperature can a 6305 bearing run?

How fast can a 6305 bearing spin? With a pressed steel cage, a 6305 reaches 14,000–15,000 RPM at oil. With a polymer cage and oil mist, 24,000–26,000 RPM is possible. Seal type matters.

  • Open: highest speed.
  • ZZ or 2Z: metal seal, lower friction.
  • 2RS or 2RS1: contact seal, lowest leak but highest friction.
  • Special grease or oil mist: higher speed.

What is the temperature range? Standard bearing steel with standard heat treatment: -30°C to +120°C continuous. For 250°C, specify high-temperature steel and clearance. For -40°C and below, confirm material and grease.

Check the grease. A 6305 with a standard lithium complex grease typically reaches +120°C. For 150°C, use an high-temperature grease and confirm with the manufacturer.

What tolerance and clearance options exist?

What are the tolerances? The bore tolerance for a 25 mm bearing per ISO 15:2017 is k5: 0 to +9 μm. Shaft tolerance for a 25 mm shaft is h6: 0 to -9 μm. Housing tolerance is H7. ABEC 1 corresponds to ISO P6, ABEC 3 to ISO P6, ABEC 5 to ISO P5, and ABEC 7 to ISO P4.

ItemABEC 1 / ISO P6ABEC 3 / ISO P6ABEC 5 / ISO P5ABEC 7 / ISO P4
Bore Δd0 to +9 μm0 to +9 μm0 to +6 μm0 to +5 μm
OD ΔD0 to -9 μm0 to -9 μm0 to -6 μm0 to -5 μm
Width ΔB0 to -12 μm0 to -12 μm0 to -8 μm0 to -5 μm
Contact angle10–18°10–18°10–18°10–18°
Surface roughness0.2–0.4 μm Ra0.2–0.4 μm Ra0.2–0.4 μm Ra0.2–0.4 μm Ra

How do I choose clearance? C3 is common for motors, gearboxes and pumps with shaft expansion or misalignment. C1 and C2 are lighter clearance. C4 or C5 are for high-temperature or high-speed cases.

What materials, cages and seals are used?

What materials? Standard bearing steel is SAE 52100 / AISI 52100, with through-hardening at 58–62 HRC. Standard 6305 bearings are usually chrome steel (GCr15). High-temperature 6305 bearings use silicon nitride (Si₃N₄) balls for thermal stability.

  • Cage: pressed steel for general use.
  • Seals: open, ZZ, 2RS, 2RS1.
  • Balls: chrome steel, silicon nitride.

What seals exist? 6305-ZZ uses metal non-contact shields. 6305-2RS uses contact rubber seals. 6305-2RS1 uses a contact lip seal. Specify the seal code in the 6305 bearing specification.

What is a 6305 bearing used for?

Where is a 6305 bearing used? Common uses are:

  • Electric motors and generators.
  • Gearboxes and speed reducers.
  • Agricultural machinery.
  • Automotive wheels and auxiliary systems.
  • Conveyors, pumps, fans, blowers.
  • Wind turbines (main shaft, yaw, pitch, generator).

What 6305 bearing should you choose? Provide:

  1. Bore, OD, width.
  2. Load rating and rpm.
  3. Temperature.
  4. Lubrication.
  5. Sealing.
  6. Tolerance class.
  7. Mounting.

A 6305-2RS works in wet pump environments. A 6305-ZZ works in dusty conveyors. A high-tolerance 6305 works in motors and machine tool spindles.

What is a 6305 bearing?

A 6305 bearing is a single-row deep groove ball bearing with a 25 mm bore, 62 mm OD and 17 mm width per ISO 15:2017. It is used in motors, gearboxes, pumps, conveyors, agricultural machinery and automotive applications.

What are the dimensions of a 6305 bearing?

25 mm bore, 62 mm OD, 17 mm width. F = 34 mm, E = 49 mm, r min = 1.0 mm, rs min = 1.0 mm, r1-2 min = 0.6 mm.

What is the load rating of a 6305 bearing?

In the 63 series, a 6305 typically has C = 22.4–23.5 kN and C₀ = 11.5–12.5 kN, depending on the manufacturer. Check the manufacturer's catalog.

How fast can a 6305 bearing spin?

A 6305 bearing can spin at 14,000–15,000 RPM with oil, and up to 24,000–26,000 RPM with oil mist and a polymer cage. The seal type affects speed.

What is the temperature range of a 6305 bearing?

Standard 6305 bearings run at -30°C to +120°C. High-temperature versions reach 250°C. Confirm steel, cage and grease with the manufacturer.

How to read a 6305 bearing specification drawing

What does a 6305 bearing drawing show? Read:

  1. Bore d = 25 mm.
  2. OD D = 62 mm.
  3. Width B = 17 mm.
  4. Sealing and shielding.
  5. Tolerance class.
  6. Material and cage.
  7. Lubrication.

A 6305 bearing specification should show the load, speed, temperature, tolerance and seal.

Share your drawing or application details at mshjzc.com for a 6305 bearing specification matched to your shaft, load, speed and lubrication.