sales@cnprv.com

+86 15862366271 (WhatsApp/WeChat)

Dynamic vs Static Load Rating: C and C0 Explained

MS Bearing WareHouse
author admin 09 November, 2026

Selecting a bearing starts with two numbers printed on every catalog page: dynamic load rating C and static load rating C0. These values define how much load a bearing can carry and how long it will last. This guide explains what C and C0 mean, how they differ, and how engineers use them to calculate bearing life.

Before diving in, review the bearing type overview so you know which bearing family applies to your machine.

Dynamic Load Rating (C)

The dynamic load rating C is a constant stationary radial load (for radial bearings) or axial load (for thrust bearings) under which the bearing can complete a rated life of one million revolutions. It is calculated from the material, geometry and size of the rolling elements and raceways.

C applies to bearings that are rotating. The higher the C value, the longer the bearing will last under a given load. C is used to calculate bearing life.

C is given in kilonewtons (kN) in catalogs. For example, a 6205 deep groove ball bearing has a C of about 14 kN, while a 6305 has a C of about 22 kN.

Static Load Rating (C0)

The static load rating C0 is the load that produces a total permanent deformation of 0.0001 times the rolling element diameter at the most heavily loaded contact point. It applies when the bearing is stationary or oscillating slowly, or when shocks occur while the machine is stopped.

Exceeding C0 causes permanent indentation (brinelling) of the raceway, which leads to noise, vibration and early failure. C0 is especially important for crane hooks, turntables and bearings that carry heavy load while not rotating.

Equivalent Dynamic Load (P)

In the real world, bearings rarely carry pure radial or pure axial load. Most applications see combined radial load Fr and axial load Fa. The equivalent dynamic load P converts this combined load into a single hypothetical radial load that would produce the same life as the actual load.

The formula is:

P = X * Fr + Y * Fa

Where:

  • Fr = applied radial load (kN)
  • Fa = applied axial load (kN)
  • X = radial load factor
  • Y = axial load factor

The X and Y values depend on the ratio Fa/C0 and the contact angle. Tables in bearing catalogs list X and Y for each series.

Basic Rating Life (L10)

The L10 life is the number of revolutions (or operating hours) that 90% of a group of identical bearings will complete before the first sign of fatigue spalling appears. The formula is:

L10 = (C / P)^p    (millions of revolutions)

Where p = 3 for ball bearings and p = 10/3 for roller bearings.

To convert to operating hours:

L10h = (10^6 / (60 * n)) * (C / P)^p

Where n = shaft speed in rpm.

Example: A 6205 bearing (C = 14 kN) carrying equivalent load P = 3 kN at 1500 rpm:

L10 = (14/3)^3 = 102 millions of revolutions
L10h = (1,000,000 / (60 * 1500)) * 102 = 1,133 hours

For critical machinery, the required L10h is typically 20,000 to 100,000 hours. If the calculated life is too short, select a larger bearing series.

Static Safety Factor (S0)

The static safety factor is the ratio C0 / P0, where P0 is the equivalent static load. Recommended values:

  • 0.5 to 1 - smooth operation, no shock (small electric motors)
  • 1 to 2 - moderate shock (gearboxes, pumps)
  • 2 to 3 - heavy shock, reversing load (cranes, rolling mills)
  • 3 to 4 - extreme shock (mining crushers, heavy excavators)

Frequently Asked Questions

What is the difference between C and C0?

C applies to rotating bearings and predicts fatigue life. C0 applies to stationary or slow-oscillating bearings and prevents permanent deformation. Both must be checked during selection.

What does L10 life actually mean?

L10 is the life that 90% of bearings will exceed. It is not the average life. The average life L50 is roughly 5 times L10, but engineers size to L10 for reliability.

Why is p = 3 for balls but 10/3 for rollers?

Roller bearings have line contact and are more tolerant of load spikes. The exponent reflects the stress-life relationship for each contact geometry.

Related Reading

Need Help with Bearing Life Calculation?

MS Bearing engineers can help you calculate C, C0 and L10 life for your specific load and speed conditions. Send us the radial load, axial load, shaft speed and operating hours, and we will recommend the bearing series that meets your design life target.