sales@cnprv.com

+86 15862366271 (WhatsApp/WeChat)

6200 Series Bearing Dimensions Guide

Home / Blogs / Info
MS Bearing WareHouse
author admin 09 November, 2026

What are 6200 series bearing dimensions? The 6200 series refers to bearings where the first two digits indicate the dimension series and width code, while the last two digits denote the bore size code multiplied by 5. For example, a bearing with code 04 has a 20 mm bore, 05 has a 25 mm bore, and 10 has a 50 mm bore (10 × 5 mm), regardless of whether the bearing is a deep groove ball, cylindrical roller, or angular contact design.

How do you read 6200 series bearing dimensions? The bore size is the primary variable, determined entirely by the last two digits; however, the outer diameter and width vary significantly depending on the specific bearing type, load capacity requirement, and whether a full-size or narrow-width variation is used. According to ISO 15:2017, the dimensional tolerances for these bearings are strictly graded, typically falling into P0 (Standard), P6, P5, or P4 classes based on application precision requirements.

Where can I find accurate 6200 series bearing dimension charts? You can find precise technical drawings and dimensional tables in the manufacturer's official catalog. Below is a breakdown of the standard identification logic and how to find exact dimensions for your specific OEM application.

6200 Series Bearing Bore Size Calculation & Identification

The bore size is the most critical dimension in the 6200 series. The calculation method is standardized across almost all rolling bearing types, making it easy to identify if a part is compatible with your existing shaft.

  • Codes 00, 01, 02, 03: For bore sizes under 10 mm, the actual millimeter size is equal to the code (e.g., 01 = 12 mm bore, per ISO 15:2017).
  • Code 04 and above: The bore size is calculated by multiplying the code by 5 (e.g., 04 × 5 = 20 mm; 10 × 5 = 50 mm).

This standardization means that a 6205 bearing (25 mm bore) will physically fit the same shaft across different load types, though the outer diameter will differ.

6200 Series Bearing Dimensions by Bearing Type

Because the "62" designation only defines the dimension series and bore, the outer diameter (OD) and width depend entirely on the bearing type. A deep groove ball bearing and a cylindrical roller bearing with the same "05" bore code will have completely different ODs.

Bearing Type Bore Code Bore Size (mm) Typical Outer Diameter (mm) Typical Width (mm)
Deep Groove Ball (6200 series) 05 25 52 15
Cylindrical Roller (NU/NJ/NUP 2205) 05 25 52 18
Angular Contact (7205) 05 25 52 15
Tapered Roller (30205) 05 25 52 16.25

The values above are typical per SKF 2024 catalog and MS Bearings factory data 2024 for standard radial designs. Always verify with the specific manufacturer's drawing for your exact load rating requirements.

Application Scenarios & Dimensional Selection

Why does the exact 6200 series bearing dimension matter for specific industries? Selecting the wrong outer diameter or width can lead to fatigue failure, housing cracking, or excessive clearance.

  • Electric Motors & Pumps: High-speed applications require precise inner ring fits. A deep groove ball bearing in the 6200 series must match the shaft tolerance (typically k6) to prevent creep.
  • Wind Power & Heavy Machinery: Larger 6200 series cylindrical roller bearings (e.g., 6216 to 6230) are used in gearboxes. Here, roller width and cage dimensions are critical for heavy radial loads.
  • Agricultural Machinery: Tapered roller bearings in the 6200 series are used in wheel hubs. The cone angle and overall width determine the axial load capacity.

Engineers must ensure that the bearing seat diameter in the housing matches the outer diameter tolerance (typically H7 or J6) to prevent rotation in the housing.

Fits, Tolerances, and Load Capacity in the 6200 Series

Can the same 6200 series bearing dimension handle different loads? No. While the bore and OD might be identical, a cylindrical roller bearing will have a significantly higher radial load capacity than a deep groove ball bearing of the exact same dimensions.

To optimize load capacity within the 6200 series, consider the following:

  1. Determine the load direction: Radial loads favor cylindrical or deep groove ball bearings; combined loads favor angular contact or tapered roller bearings.
  2. Check the clearance: Standard clearance (C2, C0, C3, C4) affects performance at high speeds. Electric motors often require C3 clearance to prevent noise and heat generation.
  3. Verify the dynamic load rating: For a 6205 deep groove ball bearing, the basic dynamic load rating is typically around 14.0 kN, while a NU2205 cylindrical roller bearing of similar dimensions can handle over 30 kN.
Expert Tip: When replacing a 6200 series bearing, never rely solely on the bore code. A 6205 replacement for a high-speed spindle application may fail if the original was an angular contact bearing requiring a specific contact angle, even if the 25 mm bore is correct.

Sourcing and Customization for 6200 Series Dimensions

Are standard 6200 series bearing dimensions always available? Yes, common codes like 05, 06, and 08 are stocked globally with short lead times. However, for specialized dimensions or modified designs, working directly with a manufacturer is recommended.

MS Bearings, based in Kunshan, Jiangsu, supplies a full range of 6200 series bearings across 10 product lines, including deep groove, cylindrical roller, tapered roller, and custom bearings. As an ISO 9001:2015 certified manufacturer founded in 2019, we provide factory-direct supply to OEMs in over 30 countries, replacing SKF, FAG, and NSK applications with a 12-month warranty and 24-hour shipping for standard sizes.

If your project requires modified 6200 series dimensions—such as custom seals, specific cage materials, or non-standard widths—our engineering team can provide technical drawings within 48 hours.

What is the bore size of a 6205 bearing?

The bore size of a 6205 bearing is 25 mm, calculated by multiplying the last two digits (05) by 5 mm per ISO 15:2017.

How do I find the outer diameter of a 6200 series bearing?

You must consult the specific bearing type and series catalog. A 6205 deep groove ball bearing has a 52 mm OD, while a NU2205 cylindrical roller bearing of the same bore has a 52 mm OD but a wider profile of 18 mm.

Are 6200 series bearing dimensions standardized globally?

Yes, bore size codes and basic dimensional series are standardized under ISO 15:2017, ensuring that a 25 mm bore bearing from MS Bearings will fit the same shaft as a 6205 bearing from SKF or FAG.

What is the MOQ for custom 6200 series bearing dimensions?

MS Bearings requires a minimum order quantity of 500 pieces for custom dimensional modifications, with standard OEM production lead times of 15-25 days.

For technical datasheets or to request a quotation for your specific 6200 series requirements, please visit mshjzc.com or contact our export team directly. We are ready to support your B2B sourcing needs with factory-direct pricing and global logistics.