What is the 6204 bearing size? A standard 6204 bearing has a bore (inner diameter) of 20 mm, an outer diameter of 47 mm, and a width of 14 mm, per ISO 15:2017. The same footprint applies whether the 6204 is an open, sealed (2RS), or shielded (ZZ) deep groove ball bearing — only the sealing element changes, not the outer envelope. All dimensions below are in millimeters unless noted.
The 6204 is one of the most widely stocked metric bearing sizes in the world because it sits in a sweet spot for electric motors, gearboxes, conveyors, pumps, and agricultural machinery. If you are replacing a bearing on existing equipment, always verify the stamped or engraved part number on the old race — a visual match alone is not proof of an identical internal clearance or seal type.
As a baseline, a 6204 with a 2RS contact rubber seal on both sides typically has a grease-filled labyrinth that tolerates up to 250°C internally, but the elastomeric lip will harden and leak above roughly 120°C continuous operation. Plan accordingly for hot shafts or high-temperature ovens.
6204 Bearing Size — Standard Dimensions Table
The table below lists the mandatory dimensions that every reputable manufacturer must match to call a part a "6204". Deviations mean the part is a copy, a "6204 clone", or a different design altogether.
| Parameter | Symbol | Value (mm) | Notes |
|---|---|---|---|
| Bore (inner diameter) | d | 20 | Per ISO 15:2017 |
| Outer diameter | D | 47 | — |
| Width | B | 14 | — |
| Radius (min) | r min | 1.0 | Edge break on chamfers |
| Radius (max) | r max | 1.5 | Must clear housing shoulder |
MS Bearings factory data from 2024 confirms that their standard 6204 production run uses r = 1.0 to 1.1 mm consistently, with a chamfer tolerance of ±0.2 mm.
6204 Bearing Size — Shaft and Housing Fit Rules
How tight should the fit be on a 6204 bearing? For rotating-inner-ring loads (the most common case), use a k5 shaft tolerance and an H7 housing bore per ISO 286-1. That combination yields a slight interference fit on the shaft (typically 2 to 5 µm for a 20 mm bore) and a small clearance on the housing (0 to +15 µm for a 47 mm OD).
- k5 shaft (20 mm): +9 µm / 0 µm — press-fit for rotating load.
- H7 housing (47 mm): 0 / +15 µm — light slip fit, especially for sealed bearings that must not migrate axially.
- Sealed 6204-2RS: Do not over-press; the seal lip can distort if the OD is forced through a tight housing with more than 10 µm interference.
Engineer's warning: If you press a 6204 onto a shaft with a k6 fit (+13 µm at 20 mm) without heating the ring, you can cold-flow the inner race and roll cage. Heat the ring to 80–90°C, never exceed 110°C for sealed variants.
6204 Bearing Size — Load Capacity and Speed Limits
How much load can a 6204 bearing take? A standard 6204 deep groove ball bearing carries roughly 12.8 kN dynamic (C) and 6.95 kN static (C0) per the SKF 2024 catalogue. These are reference values; actual life depends heavily on internal clearance class (C2, C3, C4) and lubrication.
- Dynamic load C: ~12.8 kN
- Static load C0: ~6.95 kN
- Limiting speed (open): 13,000–15,000 RPM with light oil
- Limiting speed (2RS): 9,000–11,000 RPM (seal friction rises with speed)
What applications suit the 6204 bearing size? The 20×47×14 mm envelope is standard for 0.55–7.5 kW electric motors, small gearboxes, pump shafts, conveyor rollers, and agricultural machines. It is also found in automotive auxiliary units (alternators, water pumps) and light machinery.
6204 Bearing Size — How to Measure and Verify in 5 Steps
- Clean the part: Wipe with a lint-free cloth. A 6204 contaminated with grease will read 0.05–0.1 mm oversized on a cheap caliper.
- Measure the bore: Use a micrometer at 0°, 90°, 180°, and 270° positions. Average the four readings. Expect 20.00 ± 0.008 mm for a P5 tolerance.
- Measure the OD: Use a ring gauge or a well-calibrated digital caliper at the midpoint of the width. Expect 47.00 ± 0.012 mm.
- Measure the width: Expect 14.00 ± 0.011 mm. A 6204 that measures 13.5 mm is a knock-off or a different series.
- Verify the marking: A genuine OEM-quality 6204 will be laser-etched or stamped with "6204" plus a manufacturer code. Hand-etching that looks like a sharpie marker is a red flag.
6204 Bearing Size — Tolerances, Materials, and What to Ask a Supplier
When sourcing 6204 bearings for OEM use, ask for written verification of these specs:
- Tolerance class: P0 (normal), P6, P5. Demand at least P6 for motor applications above 1800 RPM.
- Internal clearance: C3 is standard for electric motors; C4 for high-temperature or high-vibration uses.
- Material: Bearing steel SAE 52100 (1.0% C, 1.45% Cr) with through-hardening to 60–64 HRC.
- Seals: 2RS = double contact rubber seal; ZZ = metal shield; open = no seal. Specify 2RS if you need IP65 protection.
- Certification: ISO 9001:2015 for the factory, not just the product.
Procurement tip: A price that is 20–30% below market for a sealed 6204 is almost never a genuine bearing. Budget roughly USD 2.50–4.00 per piece for a factory-direct 6204-2SRSS1 in 2024–2025 market conditions; anything lower signals counterfeit material.
What is the bore size of a 6204 bearing?
The bore of a 6204 bearing is 20 mm, and the outer diameter is 47 mm, with a width of 14 mm, per ISO 15:2017. The same dimensions apply to open, sealed, and shielded variants.
Are 6204 and 6204-2RS bearings the same size?
Yes, the 6204 and 6204-2RS share the identical 20×47×14 mm envelope. The 2RS designation only adds two contact rubber seals; the outer race width is unchanged.
Can a 6204 bearing be used in a high-speed electric motor?
Yes, an open 6204 can reach 13,000–15,000 RPM with proper oil lubrication; the 2RS sealed version drops to roughly 9,000–11,000 RPM because seal friction increases with speed.
What is the standard shaft tolerance for a 6204 bearing?
For a rotating inner ring, use a k5 shaft (+9 µm at 20 mm) per ISO 286-1. This yields a 2–5 µm interference fit, sufficient for most motor and gearbox shafts.
If you are specifying 6204 bearings for an OEM motor, pump, or conveyor line, verify the full dimension envelope and tolerance class with your supplier before placing a repeat order. MS Bearings in Kunshan, China, manufactures 6204 bearings in open, ZZ, and 2RS forms under ISO 9001:2015, with 12-month warranty and 24-hour dispatch on standard SKUs. Specification sheets and sample requests are available at mshjzc.com.
