The suffixes ZZ, 2RS, C3, and P5 stamped after a deep groove ball bearing number each define one physical feature: ZZ means metal shields on both sides, 2RS means rubber contact seals on both sides, C3 means radial internal clearance larger than standard, and P5 means the bearing is ground to tolerance class 5, tighter than normal production grade. None of them changes the boundary dimensions — a sealed 6205 has exactly the same 25 × 52 × 15 mm envelope as an open one per ISO 15:2017 — so seal type, clearance and precision can be combined freely to suit the application. The marking system follows the DIN 623-1 designation convention used by SKF, FAG, NSK, NTN and virtually every manufacturer in Asia, which is why a 2RS bearing from a Chinese factory directly replaces an SKF 2RS1 or an NSK DDU without any design change.
ZZ Meaning: Metal Shields on Both Sides
ZZ (written 2Z by SKF and FAG) denotes two pressed-steel shields fixed into the outer ring. The shield does not touch the rotating inner ring, so it adds almost no friction torque and preserves the full open-bearing limiting speed per the SKF 2024 catalog. Shields block coarse dust, chips and splashed oil but do not seal against water, mist or fine powder; the bearing arrives grease-filled for life.
- Non-contact design: near-zero added torque, catalog speed unchanged
- Steel construction: the shield survives the full grease temperature range, typically −30 °C to +120 °C
- Best for fan motors, power tools, office equipment and dry indoor conveyors
- Weakness: no protection against washdown, rain, condensation or abrasive powder
2RS Meaning: Rubber Contact Seals and Their Brand Aliases
2RS means two NBR (nitrile rubber) lip seals carried in sheet-metal rings. The lip runs under light preload on the inner-ring shoulder, so friction torque rises measurably and the catalog limiting speed drops slightly versus a shielded bearing per the SKF 2024 catalog. NBR seals handle continuous service from about −30 °C to +100 °C; FKM (fluorocarbon) options extend this to roughly +150 °C, which matters for pumps and compressors near hot process lines. The same seal design carries different suffixes by brand, and buyers should treat them as functionally identical:
- 2RS1 — SKF
- 2RSR — FAG and INA
- DDU — NSK
- LLU — NTN
Practical tip: NBR degrades in caustic food-washdown chemicals and above +100 °C. For dairy, beverage or hot-oil duty, specify FKM seals or all-stainless sealed variants instead of standard 2RS.
ZZ or 2RS: How to Choose the Sealing Suffix
| Factor | ZZ (shields) | 2RS (rubber seals) |
|---|---|---|
| Contact with inner ring | None | Light lip contact |
| Water and mist protection | Poor | Good |
| Friction torque | Almost zero | Noticeably higher |
| Limiting speed | Full open-bearing value | Slightly reduced |
| Seal temperature limit | Grease-limited, about +120 °C | −30 °C to +100 °C (NBR) |
| Relubrication | Possible in housings with lube holes | Not practical; maintenance-free |
| Typical duty | Fan motors, power tools | Water pumps, conveyor rollers, agricultural machinery |
A workable field rule: choose 2RS whenever moisture, washdown or fine dust is present; choose ZZ when only coarse dust exists and maximum speed matters.
C3 Meaning: Radial Internal Clearance
C3 is a radial internal clearance group — the distance one ring can move radially relative to the other before mounting. CN (also written C0) is the standard group; C3 is one step larger. Values per ISO 5753 for deep groove ball bearings with 24–30 mm bores:
| Group | Radial clearance (µm) | When to specify |
|---|---|---|
| C2 | 1–11 | Precision, cool-running, light fits |
| CN (C0) | 5–20 | Default; loose or transition fits |
| C3 | 13–28 | Interference fits, warm-running assemblies |
| C4 | 23–41 | Hot environments; both rings interference-fitted |
C3 is the default clearance for electric motors for three reasons:
- A press-fitted inner ring expands on the shaft and consumes clearance
- Rotor heat reaches the inner ring before the outer ring, shrinking clearance further
- Operating clearance must stay positive — if it closes to zero, the balls preload, heat spikes and the bearing seizes
Warning: Do not overspecify clearance. C4 on a lightly fitted fan bearing raises vibration and noise. Shaft fits of k5 or m5, or ambient temperatures above roughly 80 °C, are the usual triggers for C3.
P5 Meaning: Tolerance Class 5
P5 is a dimensional and running-accuracy grade defined in ISO 492. It tightens bore, outside-diameter, width and radial-runout tolerances from the normal P0 grade down to single-digit microns. For a 25 mm bore:
| Class | Bore deviation (µm) | Typical duty |
|---|---|---|
| P0 (normal) | 0/−10 | General machinery, standard motors |
| P6 | 0/−8 | Better-grade electric motors, fans |
| P5 | 0/−6 | Machine-tool spindles, high-speed motors, instrumentation |
| P4 | 0/−5 | Precision spindles, aerospace equipment |
P5 controls geometry only — not seals or clearance — and is commonly ordered as a combination such as C3 + P5 for a high-speed spindle. The tighter OD, width and runout limits explain the price premium over P0; standard motor and conveyor duty rarely justifies it.
How to Read a Full Designation, Suffix by Suffix
Take 6205-2RS-C3-P5 as a worked example:
- 6205 — light series, 25 mm bore, 52 mm outside diameter, 15 mm width per ISO 15
- 2RS — NBR contact seals on both faces
- C3 — clearance group larger than normal
- P5 — tolerance class 5
Notation order and spelling vary by brand — NSK writes 6205DDUC3, SKF writes 6205-2RS1/C3, FAG writes 6205-2RSR-C3 — but the engineering content is identical. Other suffixes you will meet on deep groove ball bearings:
- N / ZNR — snap-ring groove, or shield plus snap ring
- M / TN — machined brass cage or pressed polyamide cage
- K — tapered bore, 1:12
- E — reinforced internal design with higher dynamic load rating
- C0 / C1 / C2 / C4 — other clearance groups
- P4 / P2 — higher precision classes
- V2 / EMQ — quiet-running electric-motor-quality grades
Frequently Asked Questions
Suffix codes are a purchasing language: once you can read ZZ, 2RS, C3 and P5, you can order an exact replacement from any factory in the world. MS Bearings, an ISO 9001:2015-certified factory in Kunshan, China, produces deep groove ball bearings in all common suffix combinations, including OEM equivalents for SKF, FAG and NSK designations, with a 12-month warranty. Stock items ship within 24 hours per MS Bearings factory data 2024, and the factory exports to buyers in more than 30 countries. If you need help decoding a designation or confirming the right clearance and seal combination for your equipment, the engineering team at en.mshjzc.com can cross-check the code and quote factory-direct.
