sales@cnprv.com

+86 15862366271 (WhatsApp/WeChat)

Tapered Roller Bearings: Geometry, Load Rating and Pairing

Home / Bearing Basics / Info
MS Bearing WareHouse
author admin 09 November, 2026

Tapered roller bearings are the preferred choice for combined heavy radial and heavy axial loads. Their tapered rollers and tapered raceways meet at a common apex on the bearing axis, ensuring true rolling contact without sliding. They are the dominant bearing type in automotive wheel hubs, differential pinions, gearboxes and heavy conveyor pulleys.

Compare with other rolling bearing families and deep groove ball bearings.

Cup-and-Cone Design

A tapered roller bearing is assembled from two separable components:

  • Cone (inner ring) - the tapered inner race with rollers and cage pre-assembled
  • Cup (outer ring) - the tapered outer race, a separate ring that slips into the housing bore

This separability is a major installation advantage. The cup can be pressed into the housing, and the cone with rollers can be fitted to the shaft independently. This is why tapered roller bearings dominate wheel hubs: the outer cup stays in the steering knuckle, and the inner cone assembly can be serviced separately.

Contact Angle and Load Direction

The tapered geometry creates an effective contact angle. Under combined load, the rollers transmit force along the line of contact. Because the contact angle is typically between 10 and 30 degrees, a single-row tapered roller bearing carries heavy radial load and heavy axial load in one direction.

Even when the applied load is purely radial, an axial force component develops internally. This is why tapered roller bearings must always be mounted in pairs - the second bearing absorbs the induced axial force from the first.

Single-Row, Double-Row and Four-Row

Single-Row (30200 / 32200 / 30300 Series)

The most common type, carrying combined load in one axial direction. Used in wheel hubs, pinion shafts and small gearboxes. Mounted in pairs in O or X arrangement.

Double-Row (35200 / 32000X Series)

Two rows of rollers in one assembly, carrying heavy radial load and bidirectional axial load. Used in large wheel hubs, machine tool spindles and rolling neck bearings.

Four-Row (38200 / 38300 Series)

Four rows of rollers for extremely high radial load in rolling mills and large gearboxes. These are very large, heavy bearings designed for continuous heavy-duty operation.

Preload and Setting

Tapered roller bearings are almost always set with a controlled preload or a slight end play. The setting is adjusted by:

  • Turning the locknut on the spindle while measuring torque to turn
  • Selective shim packs between the housing and end cover
  • Threaded adjusters on the bearing cone

Too much preload causes rapid overheating and failure. Too little preload allows play, which ruins gear meshing and causes wheel wobble. Automotive wheel bearings are typically set to a light preload measured by the drag torque required to rotate the hub.

Typical Applications

  • Automotive wheel hubs (front and rear, light and heavy trucks)
  • Differential pinion and pinion support bearings
  • Industrial gearboxes and speed reducers
  • Conveyor pulleys and belt idlers
  • Construction machinery (wheel loaders, excavator swing)
  • Agricultural machinery (tractor wheel hubs, pivot spindles)

Frequently Asked Questions

Can I run a single tapered roller bearing without a pair?

No. A single tapered roller bearing generates an internal axial force reaction that must be countered by a second bearing. Running one alone causes the cone to climb off the cup and catastrophic failure.

What is the difference between 30205 and 32205?

30205 is the light-series tapered roller bearing; 32205 is the wide (heavy) series. They share the same 25 mm bore but 32205 has a wider cross-section and higher load capacity.

How do I know the correct preload for a wheel bearing?

Follow the vehicle or machine manufacturer's specification. As a rough rule, wheel bearings are set so the hub can rotate smoothly by hand with zero perceptible play, but the locknut is not overtightened. A torque wrench method with rotation between passes is standard in automotive service.

Related Reading

Need Tapered Roller Bearings?

MS Bearing supplies single-row, double-row and four-row tapered roller bearings in metric and inch sizes, including 30200, 32200, 30300, 32300 and popular inch series. All cups and cones are interchangeable with major brands, CE certified and backed by a 24-month warranty. Send us your bearing number or dimensions, and we will confirm factory-direct pricing within 24 hours.