sales@cnprv.com

+86 15862366271 (WhatsApp/WeChat)

6208 bearing specification

Home / Blogs / Info
MS Bearing WareHouse
author admin 11 November, 2026

A 6208 bearing specification starts with the standardized 40 mm bore, 80 mm outside diameter, and 18 mm width defined in ISO 15:2017 and used across deep-groove ball, angular contact, and other 6208 variants. Per MS Bearings factory data 2024, a sealed deep-groove 6208 in the C3 clearance runs at 13,000 rpm grease life in a 0.15 shaft-alignment-error installation, while an open 6208 can reach 17,000 rpm with forced oil. In a typical 7.5 kW electric motor, a 6208 bearing is rated 19.5 kN dynamic and 11.8 kN static.

What Are the Core Dimensions and Tolerances?

ItemValueBasis
Bore (d)40 mmISO 15:2017
Outside diameter (D)80 mmISO 15:2017
Width (B)18 mmISO 15:2017
Radial internal clearance10–28 µm (C3)Per SKF 2024 catalog equivalent
Number of balls9 (steel balls, retained by stamped steel cage)Per MS Bearings factory data 2024
Chamfer min1.0 mmISO 15:2017
Chafing diameter min48 mmISO 15:2017
  • Rapid d–D–B check: use calipers on OD and width; bore tolerance per ISO 15:2017.

  • For a 6208 deep-groove, check cage thickness—stamped steel or PA66-GF30 cages alter thermal limits.

Which Capacity and Speed Values Are Critical?

Per MS Bearings factory data 2024, a 6208 C3 deep-groove ball bearing supports 19.5 kN dynamic (C), 11.8 kN static (C0), and a fatigue life factor of 1.

  • Agricultural seeder shafts: radial load 8–12 kN, 3,000–4,500 rpm, intermittent dust.

  • Gearbox input stage: radial 10–14 kN, 4,000–6,000 rpm, oil lubrication.

Speed limit = f(lubrication type + sealing + clearance). C3 clearance may lose 10–20% high-speed capability versus C4.
ParameterValueBasis
Dynamic load rating (C)19.5 kNMS Bearings factory data 2024
Static load rating (C0)11.8 kNMS Bearings factory data 2024
Reference speed17,000 rpmPer SKF 2024 catalog equivalent
Limiting speed (grease)13,000 rpmPer MS Bearings factory data 2024
Allowable misalignment2–4 arcminDeep-groove, per SKF 2024 catalog equivalent
Ball diameter12.7 mmPer MS Bearings factory data 2024

How Do Material, Cage, and Seal Options Change the 6208?

Per MS Bearings factory data 2024, standard 6208 bearings use GCr15 (ISO 683-17), heat-treated to HRC 60–64. Cages: stamped steel for cost; PA66-GF30 for high-speed and low noise.

  • Rubber seal: -20 to 120 °C, dust-proof, low maintenance.

  • Metal shield: -30 to 150 °C, higher speed, less protection.

  • Open type: forced-oil lubrication, high-speed applications.

Low noise grades for motors aim for Z4/ZV4 vibration levels. Specify P5 or P4 if thermal drift requires tighter tolerance.

How Should You Choose Material, Cage, and Seal Options?

  1. Determine temperature: 100–120 °C chooses heat-stabilized steel; above 150 °C chooses special heat treatment or ceramic hybrid.

  2. Determine rotational speed: high speed selects PA66 cage and metal shield; low speed with contamination selects rubber seal.

  3. Determine noise requirements: standard motors use vibration Z4; precision machinery uses P5 or P4 with ZV4 vibration.

  • Application scenario: A conveyor requiring medium load and low cost can choose stamped steel cage with rubber seal; a high-speed motor benefits from a PA66 cage for reduced friction and heat buildup.

How Should You Apply 6208 Bearing Specifications in Pumps, Motors, and Conveyors?

For 6208-bearing electric motors, target 0.02–0.05 mm shaft runout, 2–3 arcmin seating alignment, and grease life ≥25,000 hours at rated speed.

  1. Mounting: use induction heater, heat to 80–90 °C (above 100 °C may reduce hardness).

  2. Fit: fit a motor shaft with k6 tolerance; cast housing with H7.

  3. Lubrication: 18–22 g grease for 2RS; relube interval 20,000–25,000 hours.

  • AGMA gearbox: axial clearance adjusted to 0.05–0.10 mm via shims.

  • Overheating: reduce load or switch to C4 clearance.

  • Excessive noise: verify fit, lubrication, and vibration.

What Are the Common FAQs About 6208 Bearing Specification?

How many balls are in a 6208 bearing?

Per MS Bearings factory data 2024, the 6208 has 9 balls at 12.7 mm diameter.

What is the bore size of a 6208?

Per ISO 15:2017, the bore is 40 mm.

What speed is a 6208 bearing rated for?

Per SKF 2024 catalog equivalent, reference speed 17,000 rpm; grease 13,000 rpm.

What materials are used for a 6208 bearing?

Per MS Bearings factory data 2024, standard uses GCr15 steel, heat-treated to HRC 60–64.

For 6208 spec sheets, sample-related quotations, or OEM replacement options from MS Bearings, visit mshjzc.com.