sales@cnprv.com

+86 15862366271 (WhatsApp/WeChat)

Preload in Bearings: When It Helps and When It Hurts

MS Bearing WareHouse
author admin 09 November, 2026

Preload is the deliberate application of a permanent axial force on a bearing, squeezing the rolling elements against the raceways to eliminate internal clearance. It increases rigidity, reduces vibration and improves running accuracy. But too much preload destroys a bearing just as surely as too little. This guide explains when preload makes sense and how much to apply.

See also angular contact bearing arrangements and load rating basics.

Why Apply Preload?

Unloaded bearings have internal clearance. Under load, the inner ring shifts axially and radially, and the shaft has a small but measurable play. In precision applications - machine tool spindles, measuring instruments, high-speed grinders - that play ruins accuracy. Preload eliminates it by stretching or compressing the bearing stack.

Preload also:

  • Increases the contact stiffness between rolling elements and raceways
  • Reduces vibration and noise at high speed
  • Minimizes skidding of rolling elements under light load
  • Improves shaft guiding accuracy

When NOT to Preload

Preload is not a universal good. Do not preload when:

  • The bearing already runs hot (electric motors, general gearboxes)
  • Load is already heavy (preload adds extra stress and shortens life)
  • Temperature varies widely (preload changes as parts expand)
  • You have no way to measure or set it precisely

Deep groove ball bearings, cylindrical roller bearings and spherical roller bearings are generally not preloaded. Preload is reserved for angular contact ball bearings, tapered roller bearings and precision spindle arrangements.

Three Preload Classes

ClassTypical UseEffect
Light (A)High-speed spindles, small motorsMinimal friction increase, maximum speed
Medium (B)General gearboxes, pumpsBalance of stiffness and speed
Heavy (C)Machine tool spindles, heavy cuttingMaximum rigidity, lower speed, more heat

How Preload Is Applied

Spring Preload

A disc spring or coil spring pushes the outer ring against the rolling elements. The preload force is constant regardless of thermal expansion. Simple and reliable, common in small motor shafts and precision instrument bearings.

Fixed Position Preload

The inner rings are clamped against each other by a locknut, and the outer rings are clamped by end covers. This sets a fixed axial position. Preload changes with temperature because the shaft expands. Common in machine tool spindles and wheel hubs.

Pair Set (Universal Matching)

Bearings are ground at the factory so that when clamped together they produce a specified preload without measurement. Marked GA (light), GB (medium), GC (heavy). This is the most common approach for precision spindle arrangements.

The Cost of Over-Preload

Preload is an extra internal load that reduces bearing life. The equivalent load P includes the preload force. Doubling the preload can reduce L10 life by a factor of two to three. Over-preloading also causes heat generation, lubricant breakdown and early spalling. Always use the minimum preload that meets your stiffness requirement.

Frequently Asked Questions

What preload class should I use for a grinder spindle?

Grinder spindles typically use light or medium preload (GA or GB) with 15 degree angular contact bearings, oil-air lubricated. The goal is high speed with enough stiffness for wheel contact.

Can I preload deep groove ball bearings?

Not effectively. Deep groove bearings are not designed for axial preload; applying it causes edge loading on the balls and early failure. Use angular contact bearings for preloaded arrangements.

How do I measure preload during assembly?

Measure the drag torque required to rotate the shaft. Manufacturer catalogs list the target drag torque for each preload class and bore size. Tighten the locknut until the measured torque falls within the specified range.

Related Reading

Need Preloaded Bearing Sets?

MS Bearing supplies universal matched angular contact bearing sets (DB, DF, DT) in light, medium and heavy preload classes. Send us your spindle speed, stiffness requirement and bore size, and our engineers will confirm the correct arrangement and preload class.